Model identification for thermal modelling of a battery pack

Experimental Demonstration of RCCI in Heavy-Duty Engines using Diesel and Natural Gas

Premixed combustion concepts like PCCI and RCCI have attracted much attention, since these concepts offer possibilities to reduce engine out emissions to a low level, while still achieving good efficiency. Most RCCI studies use a combination of a high-cetane fuel like diesel, and gasoline as low-cetane fuel. Limited results have been published...

Experimental study into a hybrid PCCI/CI concept for next-generation heavy-duty diesel engines

This paper presents the first results of an experimental study into a hybrid combustion concept for next-generation heavy-duty diesel engines. In this hybrid concept, at low load operating conditions, the engine is run in Pre-mixed Charge Compression Ignition (PCCI) mode, whereas at high load conventional CI combustion is applied. This study was...

Direct injection of high pressure gas: Scaling properties of pulsed turbulent jets

Existing gasoline DI injection equipment has been modified to generate single hole pulsed gas jets. Injection experiments have been performed at combinations of 3 different pressure ratios (2 of which supercritical) respectively 3 different hole geometries (i.e. length to diameter ratios). Injection was into a pressure chamber with optical...

Gas density and rail pressure effects on diesel spray growth from a heavy-duty common rail injector

Formation of nonevaporating sprays from diesel fuel injection through a realistic heavy duty multihole common rail injector is studied in a newly developed high-pressure, high-temperature cell, using digital highspeed shadowgraphy at 4500 frames/s. Gas pressure was varied from 13 to 37 bar (corresponding to densities of 15-42 kg/m3, using N2 at...

Biodiesel soot incandescence and NO emission studied in an optical engine

High-speed imaging and thermodynamical characterization are applied to an optically accessible, heavy-duty diesel engine in order to compare soot incandescence and NO emission behaviour of four bioderived fuels: rapeseed-methylester, Jatropha oil (pure), Jatropha-methylester and a 50/50 blend of cyclohexanone with a Fischer-Tropsch synthetic...

Cyclic oxygenates: A new class of second-generation biofuels for diesel engines?

Combustion behavior of various oxygenated fuels has been studied in a DAF heavy-duty (HD) directinjection (DI) diesel engine. From these fuels, it is well-known that they lead to lower particle (PM) emissions; however, for a given fuel oxygen mass fraction, there are significant differences in PM reduction. Although this can be traced back to...

SCR-only concept for heavy-duty Euro-VI applications

Soot and chemiluminescence in diesel combustion of bio-derived, oxygenated and reference fuels

High-speed imaging, spectroscopy and thermodynamical characterization are applied to an optically accessible, heavy-duty diesel engine in order to compare sooting and chemiluminescence behaviour of bio-derived, oxygenated fuels and various reference fuels. The fuels concerned include the bio-derived fuels Jatropha oil (pure), Jatropha...

Experimental validation of extended NO and soot model for advanced HD diesel engine combustion

A computationally efficient engine model is developed based on an extended NO emission model and state-of-the-art soot model. The model predicts exhaust NO and soot emission for both conventional and advanced, high-EGR (up to 50%), heavy-duty DI diesel combustion. Modeling activities have aimed at limiting the computational effort while...

Uncooled EGR as a means of limiting wall-wetting under early direct injection conditions

Collision of injected fuel spray against the cylinder liner (wall-wetting) is one of the main hurdles that must be overcome in order for early direct injection Premixed Charge Compression Ignition (EDI PCCI) combustion to become a viable alternative for conventional DI diesel combustion. Preferably, the prevention of wall-wetting should be...

Optimization of operating conditions in the early direct injection premixed charge compression ignition regime

Early Direct Injection Premixed Charge Compression Ignition (EDI PCCI) is a widely researched combustion concept, which promises soot and CO2 emission levels of a spark-ignition (SI) and compression-ignition (CI) engine, respectively. Application of this concept to a conventional CI engine using a conventional CI fuel faces a number of...

Alternative fuel options for urban bus application in the Netherlands: a comparative study

Today, a large number of urban areas in the Netherlands face significant local air quality problems. One source of this local pollution is road traffic and, in urban areas, public transport by city bus. For this reason, there is a lot of interest in different opportunities to lower the harmful emissions from city buses. A possible method to do...

Efficient EGR technology for future HD diesel engine emission targets

Different systems for achieving short-route cooled EGR on turbocharged and aftercooled heavy-duty diesel engines have been tested on a 12 litre 315 kW engine with 4 valves per cylinder and an electronically controlled unit pump fuel injection system. In all of these systems the exhaust gas was tapped off before the turbine, cooled and mixed with...

Evaluating piezo-electric transducer response to thermal shock from in-cylinder pressure data

One of the major effects limiting the accuracy of piezo-electric transducers for performing in-cyclinder pressure measurements is their sensitivity to the cyclic thermal loading effects of the intermittent combustion process. This paper compares 5 different methods for evaluating the effect of this co-called thermal shock from the measured...

EGR technology for lowest emissions

An EGR system for turbocharged and aftercooled HD diesel engines has been demonstrated on a 12 litre 315 kW engine with 4 valves per cylinder and a high pressure injection system. In this system exhaust gas is tapped off before the turbine, run through a cooler and mixed with the intake air after the compressor and aftercooler. The EGR system...

New EGR technology retains HD diesel economy with 21st century emissions

An EGR system for turbocharged (and aftercooled) heavy-duty diesel engines have been demonstrated on a 12 litre 315 kW engine with 4 valves per cyclinder head and high pressure injection system. In the EGR system exhaust gas is tapped of before the turbine, run through a cooler and mixed with the intake air after the compressor and aftercooler....